+ Reply to Thread
Results 1 to 4 of 4

Thread: WC7555 Xerox no swithched mode

  1. #1
    Join Date
    May 2010
    Posts
    4

    Default WC7555 Xerox no swithched mode

    does the 7555 work in switched mode?>

    simular to the other fierys.
    ?
    after installing the connected mode and switching the cables
    staticked the ips the fiery cannot get to the printer......

  2. #2
    thistlegorm is offline Fiery Forum Expert Contributor thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status
    Join Date
    Jul 2009
    Location
    London UK
    Posts
    522

    Default

    Hi,

    Not sure I understand what you asking ? do you mean does the 7556 (7555 - doesn't exist) support Network Switch Connection ? ie the EFI server & IOT Controller have seperate IP addresses ? as opposed from a Direct connection whereby the controller on the IOT has 100.100.100.102 as an IP address.
    My understanding is that it does not support it - the Workcentre 77XX series with the new discovery IOT controller does - if you want to, can you post a config report ? & I will check the software version

  3. #3
    Join Date
    Jul 2009
    Posts
    1

    Default Network spe******t Veenman B.V.

    What sthompson meens is DualIP configuration.
    Is it possible to configure the Xerox 75xx with fiery for Dualip configurattion.
    so that you can print to the Xerox controller and the Fiery controller with 2 different drivers?

  4. #4
    thistlegorm is offline Fiery Forum Expert Contributor thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status thistlegorm has achieved rock star status
    Join Date
    Jul 2009
    Location
    London UK
    Posts
    522

    Default

    Ok - as I thought Dual IP ( Using Network Switch ) is not supported- basically because you do not need it.

    Everthing goes through the 1 x IP address.

    1. Set the 75XX IOT controller to DHCP via the GUI.
    2. Power down both the IOT controller & the optional Fiery Controller.
    3. With both of them powered down confirm the crossover cable is correctly installed from the IOT to the Fiery & the clients network cable is correctly installed.
    4. Switch on IOT & wait for it to come ready (approx 3-4 mins ) , then Power on the Fiery - when both are ready you should get a startup page with the customers IP address if DHCP is supported, else you should be able to configure the Fiery basics from the 75XX GUI using Webtools.

    You can now configure your Fiery Print Driver Port to Point to Hold or Print on the Fiery.

    If you have users that do not want to use the Fiery & simply want to have a quick print come out - then all you need to do is install another printer using the Fierys IP address & the Xerox Controller Print Driver - however configure the Port setting to Port 9200 - this will bypass the Fiery print queues & go direct to the Xerox controller.

    Hope that helps

+ Reply to Thread

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts